$50.49 $59.99 Buy It Now

How to replace back camera glass on iphone 7 plus

0

Accidents happen, and sometimes the back camera glass on your iPhone 7 Plus may crack or shatter. Instead of replacing the entire device, you can opt to replace just the back camera glass to restore the functionality and aesthetics of your phone. This may seem like a daunting task, but with the right tools and a careful approach, you can successfully replace the back camera glass on your iPhone 7 Plus.

In this guide, we will walk you through the step-by-step process of replacing the back camera glass on your iPhone 7 Plus. From preparing the necessary tools to safely removing the broken glass and installing the new one, we will provide detailed instructions to help you complete the repair seamlessly. Follow along and give your iPhone 7 Plus a fresh new look!

Step-by-Step Guide to Replacing Back Camera Glass on iPhone 7 Plus

Accidents happen, and if the back camera glass on your iPhone 7 Plus is cracked or damaged, you can replace it yourself with a few tools and a bit of patience. Follow these steps to replace the back camera glass on your iPhone 7 Plus:

  1. Gather Your Materials: You will need a replacement back camera glass, a small Phillips screwdriver, a heat gun or hairdryer, a suction cup, a plastic pick or spudger tool, and tweezers.
  2. Power Off Your iPhone: Make sure your iPhone is turned off before you begin the repair process.
  3. Remove the Two Pentalobe Screws: Use the small Phillips screwdriver to remove the two screws at the bottom of your iPhone.
  4. Heat the Back of Your iPhone: Use the heat gun or hairdryer to heat the back of your iPhone for about 1-2 minutes to soften the adhesive under the back glass.
  5. Use the Suction Cup: Place the suction cup near the bottom edge of the back glass and gently pull to create a small gap between the back glass and the iPhone.
  6. Insert the Pick Tool: Once you have a small gap, insert the plastic pick or spudger tool to carefully pry the back glass away from the iPhone.
  7. Replace the Back Camera Glass: Once the back glass is removed, locate the back camera glass and gently pry it out using the tweezers.
  8. Install the New Camera Glass: Place the new back camera glass in the correct position and press it firmly to secure it in place.
  9. Reassemble Your iPhone: Reattach the back glass, screw in the two Pentalobe screws, and power on your iPhone to ensure the back camera is working properly.

Final Thoughts

Replacing the back camera glass on your iPhone 7 Plus may seem daunting, but with the right tools and careful steps, you can successfully complete the repair. Remember to take your time and follow each step closely to avoid causing further damage to your device.

See also  Who makes iphone 6 plus camera

Gather Necessary Tools and Materials

Before you start the process of replacing the back camera glass on your iPhone 7 Plus, make sure you have all the necessary tools and materials at hand. Here is a list of items you will need:

Tools:

  • Pentalobe screwdriver
  • Phillips screwdriver
  • Plastic spudger tool
  • Heat gun or hair dryer
  • Tweezers
  • Cloth or microfiber towel

Materials:

  • Replacement back camera glass (make sure it is compatible with iPhone 7 Plus)
  • Adhesive tape or glue for securing the new glass

Having these tools and materials ready will ensure a smoother and more efficient replacement process. Make sure to work in a well-lit and clean area to avoid losing any small parts during the repair.

Power Off Your iPhone 7 Plus

Before starting the camera glass replacement process, make sure to power off your iPhone 7 Plus to avoid any potential damage or accidents. To power off your device, press and hold the power button located on the right side of the phone. Slide the on-screen prompt to power off your device completely. Once the phone is turned off, you can proceed with the camera glass replacement safely.

Remove the Back Cover of Your iPhone 7 Plus

To replace the back camera glass on your iPhone 7 Plus, you will first need to remove the back cover of the device. Follow these steps carefully to safely remove the back cover:

  1. Power Off: Make sure your iPhone is powered off before beginning the repair process.
  2. Tools: Gather the necessary tools such as a pentalobe screwdriver and a suction cup.
  3. Remove Screws: Use the pentalobe screwdriver to remove the screws located at the bottom of the iPhone near the charging port.
  4. Use Suction Cup: Place the suction cup near the home button and gently lift to create a small gap between the back cover and the device.
  5. Slide Tool: Insert a thin tool or pick into the gap created and carefully slide it along the edges to release the clips holding the back cover in place.
  6. Remove Cover: Once all clips are released, lift the back cover away from the iPhone and set it aside.

With the back cover removed, you can now proceed with replacing the back camera glass on your iPhone 7 Plus. Be sure to follow the appropriate steps and handle the components with care to avoid any damage during the repair process.

See also  How to sync pictures from computer to iphone camera roll

Locate and Access the Back Camera Glass

Before you start the replacement process, you need to locate and access the back camera glass on your iPhone 7 Plus. Here’s how you can do it:

  1. Power off your iPhone and remove the SIM card tray.
  2. Use a Pentalobe screwdriver to remove the two screws at the bottom of the device.
  3. Apply gentle heat using a hairdryer or heat gun to soften the adhesive around the edges of the back cover.
  4. Insert a suction cup near the bottom edge of the back cover and gently pull to create a small opening.
  5. Slide a plastic spudger along the sides to release the clips holding the back cover in place.
  6. Once the back cover is removed, locate the back camera glass near the top left corner of the device.

Now that you have located and accessed the back camera glass, you can proceed with the replacement process. Be sure to handle the components with care to avoid any damage.

Remove the Old Damaged Camera Glass

To begin the process of replacing the back camera glass on your iPhone 7 Plus, you will first need to remove the old damaged camera glass. This step is crucial to ensure a clean and smooth installation of the new camera glass.

Start by heating the edges of the camera glass with a heat gun or hair dryer to soften the adhesive holding it in place. Be careful not to overheat the glass, as it can cause damage to the surrounding components.

Once the adhesive is softened, gently pry the old camera glass off using a plastic opening tool or a small suction cup. Take your time and work gradually to avoid damaging the camera lens or the rear camera module.

After removing the old camera glass, make sure to clean any remaining adhesive residue from the camera lens and the surrounding area using isopropyl alcohol and a lint-free cloth. This will ensure a secure bond when installing the new camera glass.

Clean the Camera Lens Area Thoroughly

Before installing the new camera glass, it is crucial to clean the camera lens area thoroughly to ensure optimal performance. Follow these steps:

1. Gather Supplies:

Prepare a microfiber cloth, lens cleaning solution, and a can of compressed air.

2. Clean the Lens:

Gently wipe the camera lens area with the microfiber cloth to remove any dust, smudges, or fingerprints. Use the lens cleaning solution if necessary, but avoid getting any liquid inside the camera.

Install the New Camera Glass

Once you have removed the old camera glass and cleaned the area, it’s time to install the new camera glass. Make sure the replacement glass is clean and free of any dust or fingerprints.

See also  How to fix iphone camera stabilizer

Carefully align the new camera glass with the opening on the back of the iPhone 7 Plus. Gently press it into place, ensuring that it sits flush with the surrounding frame.

Step 1: Align the Glass

Align the replacement camera glass with the opening on the back of the iPhone, making sure it is positioned correctly.

Reassemble Your iPhone 7 Plus

Now that you have successfully replaced the back camera glass on your iPhone 7 Plus, it’s time to reassemble the device. Follow these steps to put everything back together:

  1. Reconnect the camera and flash cables: Carefully reconnect the camera and flash cables to the logic board, making sure they are securely in place.
  2. Replace the rear camera: Insert the rear camera module back into its housing and secure it with the screws.
  3. Reinstall the logic board: Carefully place the logic board back into the iPhone, making sure all the connectors are properly aligned.
  4. Reattach the display assembly: Reconnect the display assembly to the logic board and press it down until it clicks into place.
  5. Secure the display: Replace the screws near the home button and reattach the metal bracket over the display connectors.
  6. Replace the SIM tray: Insert the SIM tray back into the iPhone.
  7. Power on your iPhone: Press and hold the power button until the Apple logo appears to ensure that the device functions properly.

Once you have completed these steps, your iPhone 7 Plus should be fully reassembled and ready to use with its new back camera glass.

Power On Your iPhone 7 Plus and Test the Camera

After successfully replacing the back camera glass on your iPhone 7 Plus, it’s time to power on the device and test the camera to ensure it’s working properly. Follow these steps to test the camera:

  1. Press and hold the power button on your iPhone 7 Plus to turn it on.
  2. Unlock the device using your passcode or Touch ID.
  3. Locate the Camera app on your home screen and tap on it to open the camera.
  4. Switch between the rear and front cameras to test both functionalities.
  5. Take a few test photos and videos to check the quality of the camera.

If the camera functions as expected without any issues, congratulations on successfully replacing the back camera glass on your iPhone 7 Plus!

Carmen J. Moore
Carmen J. Moore

Carmen J. Moore is an expert in the field of photography and videography, blending a passion for art with technical expertise. With over a decade of experience in the industry, she is recognized as a sought-after photographer and videographer capable of capturing moments and crafting unique visual narratives.

Camera Reviews
Logo