Are you looking to replace or repair the front facing camera on your iPhone 6s? Removing the front facing camera on an iPhone 6s may seem like a daunting task, but with the right tools and guidance, you can do it yourself.
In this guide, we’ll walk you through the steps to safely remove the front facing camera on your iPhone 6s. It’s important to follow these steps carefully to avoid damaging your device.
Before you begin, make sure you have the necessary tools, including a small Phillips screwdriver, a plastic opening tool, and a spudger. Additionally, be sure to power off your iPhone and disconnect any cables or accessories.
Step-by-Step Guide to Removing iPhone 6s Front Facing Camera
Step 1: Power off your iPhone 6s and remove the two screws located at the bottom of the device using a pentalobe screwdriver.
Step 2: Use a suction cup to lift the display assembly slightly and insert a plastic opening tool between the display and the rear case to separate them.
Step 3: Carefully lift the display assembly and lean it against something to prevent straining the cables.
Step 4: Locate the front facing camera module near the top of the device and disconnect the cables attached to it using a spudger tool.
Step 5: Gently pry the front facing camera module away from its housing using a spudger tool or your fingers.
Step 6: Once the front facing camera is free, remove it from the device and replace it with a new one if necessary.
Step 7: Reassemble your iPhone 6s by following the steps in reverse order, making sure all cables are properly connected and the screws are tightened securely.
Gather Necessary Tools
Before starting the process of taking the iPhone 6s front-facing camera off, you will need to gather some essential tools. Here is a list of tools you will require:
| 1. Small Phillips head screwdriver |
| 2. Plastic opening tools |
| 3. Tweezers |
| 4. Spudger tool |
Power Off Your iPhone 6s
To turn off your iPhone 6s, follow these steps:
| 1. | Press and hold the power button located on the right side of your iPhone. |
| 2. | Simultaneously press and hold the volume down button on the left side of your iPhone. |
| 3. | Continue holding both buttons until the “slide to power off” slider appears on the screen. |
| 4. | Slide the slider to the right to power off your iPhone 6s. |
Remove the Display Assembly
To access the front facing camera on your iPhone 6s, you will first need to remove the display assembly. Follow these steps to do so:
-
Power off your iPhone and remove the two pentalobe screws located at the bottom of the device.
-
Use a suction cup to lift the display assembly slightly.
-
Slide an opening pick or a thin plastic card between the display assembly and the frame to separate the adhesive.
-
Work your way around the edges of the display assembly to loosen it from the adhesive holding it in place.
-
Once the display assembly is separated, carefully lift it up and support it at a 90-degree angle to the frame.
Disconnect the Battery
Before working on the front facing camera of your iPhone 6s, it is crucial to disconnect the battery to prevent any damage to the device.
Step 1: Power Off the Device
Make sure your iPhone 6s is powered off completely before proceeding with the battery disconnection.
Step 2: Remove the Screws
Use the appropriate screwdriver to remove the screws securing the back cover of your iPhone 6s.
Caution: Be gentle while removing the screws to avoid stripping them.
Once the screws are removed, carefully lift off the back cover to reveal the internal components.
Note: It is recommended to follow a detailed guide or watch a tutorial video to ensure proper disassembly of your device.
Remove the Front Camera Bracket
Removing the front camera bracket is a crucial step in taking off the iPhone 6s front-facing camera. Follow these steps to safely remove the bracket:
- Using a small Phillips screwdriver, carefully unscrew the screws securing the bracket in place.
- Gently lift the bracket off the camera module to expose the front camera.
- Be cautious not to damage any other components while removing the bracket.
Once the bracket is removed, you can proceed with disconnecting the front-facing camera from the motherboard and replacing it if necessary.
Disconnect the Front Camera Flex Cable
To disconnect the front camera flex cable on your iPhone 6s, follow these steps:
Step 1: Power Off Your iPhone
Before you begin, make sure to power off your iPhone to avoid any damage to the device.
Step 2: Remove the Display Assembly
Next, carefully remove the display assembly of your iPhone 6s to access the front camera flex cable.
Once the display assembly is removed, locate the front camera flex cable connector and gently disconnect it from the logic board.
Make sure to handle the flex cable with care to avoid any damage.
Remove the Front Facing Camera
If you need to remove the front facing camera from your iPhone 6s, follow these steps:
Step 1: Gather the necessary tools
Before you begin, make sure you have the required tools such as a small Phillips head screwdriver, a plastic opening tool, and a spudger.
Step 2: Disassemble the iPhone
Start by turning off your iPhone and removing the two screws located on both sides of the lightning connector. Use the plastic opening tool to carefully pry open the display assembly from the rear case. Be gentle to avoid damaging the components.
Continue disassembling the iPhone by removing the screws that secure the front facing camera module in place. Use the spudger to disconnect the camera module from the logic board.
Once the front facing camera is disconnected, you can carefully remove it from the iPhone.
Install the New Front Facing Camera
Once you have removed the old front facing camera, it’s time to install the new one.
Step 1: Carefully position the new front facing camera in place, making sure it aligns correctly with the housing.
Step 2: Gently press the camera into the housing, ensuring it sits securely in place.
Step 3: Reconnect the ribbon cable to the motherboard, making sure it is properly aligned and seated.
Step 4: Carefully reattach any screws or adhesive that hold the camera in place.
Step 5: Once the new camera is securely installed, reassemble your iPhone 6s by following the steps in reverse order.
Remember to test the new front facing camera to ensure it is functioning properly before fully reassembling your device.
Reassemble Your iPhone 6s
Once you have successfully removed the front facing camera from your iPhone 6s, it’s time to reassemble everything. Follow these steps to put your device back together:
| 1. | Carefully place the front facing camera back in its original position on the front panel. |
| 2. | Reconnect the flex cable of the front facing camera to the logic board. |
| 3. | Gently place the front panel back on the device, making sure all the clips are aligned and secure. |
| 4. | Tighten all the screws that hold the front panel in place. |
| 5. | Once the front panel is securely attached, power on your iPhone 6s to test the front facing camera. |
| 6. | If the camera is functioning properly, proceed to put back any remaining components such as the display assembly and battery. |
| 7. | Finally, replace the back cover of your iPhone 6s and secure it with the necessary screws. |
