If you own an iPhone 6s Plus and notice that the camera lens cover is scratched or cracked, it’s important to replace it to ensure your camera continues to function properly. Replacing the camera lens cover on your iPhone 6s Plus is a relatively simple process that can be done at home with the right tools and a bit of patience.
In this guide, we’ll walk you through the steps to safely replace the camera lens cover on your iPhone 6s Plus. By following these instructions carefully, you’ll be able to restore your camera’s clarity and protect it from further damage.
Before you begin, make sure you have a replacement camera lens cover that is compatible with the iPhone 6s Plus model. You’ll also need a small Phillips screwdriver, a flat tool like a plastic opening tool or a spudger, and a hairdryer or heat gun to soften the adhesive.
Step-by-Step Guide to Replacing iPhone 6s Plus Camera Lens Cover
If you’ve noticed any scratches or cracks on your iPhone 6s Plus camera lens cover, it may be time to replace it. Follow these steps to do it yourself:
Step 1: Gather the necessary tools, including a replacement camera lens cover, a small Phillips screwdriver, and a plastic prying tool.
![Simtect for Samsung Galaxy S24 Ultra Case with Camera Cover, [Non-Yellowing] [Military Drop Protection], Slim Protective Hard Back and Soft Edge Phone Case for Galaxy S24 Ultra Case 6.8 Inches, Clear](https://m.media-amazon.com/images/I/51Ji1BuLyaL._SS520_.jpg)
Step 2: Power off your iPhone and remove the two screws located next to the charging port using the Phillips screwdriver.
Step 3: Use the plastic prying tool to carefully separate the back cover from the rest of the phone. Be gentle to avoid damaging any components.
Step 4: Locate the camera lens cover and gently pry it off the phone. Be careful not to damage the camera lens itself.
Step 5: Place the new camera lens cover in position and press down firmly to secure it in place.
Step 6: Reassemble your iPhone by following the steps in reverse order. Make sure to tighten the screws securely.
Step 7: Power on your iPhone and test the camera to ensure that the new lens cover is working properly.
By following these steps, you can easily replace the camera lens cover on your iPhone 6s Plus and keep your device looking like new.
Gather Necessary Tools and Materials
Before replacing the camera lens cover on your iPhone 6s Plus, make sure you have all the necessary tools and materials ready. Here is a list of items you will need:
- Replacement camera lens cover
- Small Phillips screwdriver
- Plastic pry tool or opening tool
- Adhesive tape
- Cloth or tissue for cleaning
- Patience and steady hands
Power Off Your iPhone 6s Plus
Before you begin replacing the camera lens cover on your iPhone 6s Plus, it is important to power off the device to prevent any damage or accidents. Follow these steps to properly power off your iPhone:
- Press and hold the power button located on the right side of the iPhone.
- Swipe the “slide to power off” option that appears on the screen to turn off your device.
Ensure that your iPhone is completely powered off before proceeding with the camera lens cover replacement process.
Remove the Screws from the Bottom of the Device
To begin the process of replacing the iPhone 6s Plus camera lens cover, you will first need to remove the screws from the bottom of the device. Use a suitable screwdriver to carefully unscrew the screws located at the bottom edge of the phone.
Make sure to keep track of the screws and store them in a safe place to avoid losing them. Once all the screws are removed, you can proceed to the next step in the camera lens cover replacement process.
Use a Suction Cup to Lift the Screen
Before you can access the camera lens cover on your iPhone 6s Plus, you’ll need to remove the screen. Start by using a suction cup to lift the screen away from the body of the phone.
Place the suction cup near the home button and gently pull up to create a small gap between the screen and the frame of the phone. Be careful not to pull too hard, as you don’t want to damage the screen.
Once you have a small gap, insert a plastic spudger or a guitar pick into the space to keep it open. Slowly slide the tool around the edges of the screen to release the adhesive holding it in place.
Continue working your way around the screen until it is free from the adhesive. Be gentle and take your time to avoid damaging any of the components inside the phone.
Disconnect the Battery Connector
Before starting the repair process, it is crucial to disconnect the battery connector to avoid any electrical damage or short circuits. Follow these steps to safely disconnect the battery connector:
- Turn off your iPhone 6s Plus.
- Remove the two pentalobe screws located at the bottom of the phone next to the charging port.
- Use a suction cup to lift the screen assembly slightly and insert a plastic spudger or opening tool to gently pry the screen away from the body of the phone.
- Locate the battery connector on the logic board and carefully lift the connector straight up to disconnect it.
Once the battery connector is disconnected, you can safely proceed with the replacement of the camera lens cover on your iPhone 6s Plus.
Remove the Front Panel Assembly
Before replacing the camera lens cover on your iPhone 6s Plus, you will need to remove the front panel assembly. Follow these steps to do so:
- Power off your iPhone and remove the two bottom screws located next to the charging port.
- Use a suction cup to lift the front panel slightly.
- Insert a plastic opening tool or a thin pry tool between the front panel and the rear case.
- Gently slide the tool along the edge to separate the adhesive holding the front panel in place.
- Open the iPhone by swinging the front panel up from the left side, like the back cover of a book.
- Be careful not to damage the display cables near the top of the phone.
Extract the Rear Camera Lens Cover
To extract the rear camera lens cover, you will need to carefully pry it out using a small, flat tool, such as a plastic spudger or a guitar pick. Start by inserting the tool between the lens cover and the camera module, then gently apply pressure to lift the cover out of its place.
Be Gentle and Patient
Take your time and be gentle while prying out the lens cover to avoid damaging the camera module or the surrounding components. It may require some patience and finesse to remove the cover without causing any harm.
Install the New Camera Lens Cover
Once you have removed the old camera lens cover, it’s time to install the new one. Follow these steps:
| 1. | Take the new camera lens cover and position it over the camera lens on the back of your iPhone 6s Plus. |
| 2. | Gently press down on the new lens cover to secure it in place. Make sure it is aligned properly. |
| 3. | Use a clean cloth to wipe away any fingerprints or smudges on the new lens cover. |
| 4. | Double-check that the lens cover is securely attached and there are no gaps around the edges. |
| 5. | Once you are satisfied with the placement, you can now test your camera to ensure the new lens cover does not affect the picture quality. |
Reassemble Your iPhone 6s Plus
Once you have successfully replaced the camera lens cover, it’s time to reassemble your iPhone 6s Plus. Follow these steps:
- Place the rear camera module back in its original position.
- Reattach the camera module with the screws you removed earlier.
- Align the camera lens cover with the camera module and press gently to secure it in place.
- Insert the rear panel back onto the iPhone and press down around the edges to snap it into place.
- Finally, reinsert the screws into the bottom of the iPhone and tighten them securely.
Once you’ve completed these steps, power on your iPhone 6s Plus and test the camera to ensure that the lens cover replacement was successful.
Power On Your iPhone and Test the Camera
Once you have successfully replaced the camera lens cover on your iPhone 6s Plus, it’s time to power on your device and test the camera to ensure everything is working correctly.
- Press and hold the power button on your iPhone to turn it on.
- Unlock your iPhone and navigate to the camera app.
- Test the rear and front camera by taking a few photos and videos.
- Check the quality of the images and videos to ensure there are no issues with the new camera lens cover.
If you notice any abnormalities or issues with the camera after replacing the lens cover, you may need to recheck the installation or seek professional help to resolve the problem.
