If you’ve accidentally shattered the rear glass camera piece on your iPhone 5s, don’t worry, you can replace it yourself with a little patience and the right tools. This guide will walk you through the steps to safely remove the broken glass and install a new rear camera piece on your iPhone 5s.
Step 1: Gather Your Tools
Before you begin, make sure you have the necessary tools on hand. You’ll need a small Phillips screwdriver, a plastic spudger tool, a suction cup, and a replacement rear glass camera piece designed for the iPhone 5s.
Step 2: Remove the Broken Glass
Start by powering off your iPhone 5s and removing the two screws located next to the lightning port. Use the suction cup to gently lift the screen assembly away from the rear case. Be careful not to damage the cables connecting the screen to the phone.
Step-by-Step Guide to Replacing iPhone 5s Rear Glass Camera Piece
Replacing the rear glass camera piece on an iPhone 5s can be a straightforward process if you follow these steps carefully. Here’s a step-by-step guide to help you through the process:
Step 1: Gather Your Tools
Before you begin, make sure you have all the necessary tools handy. You’ll need a small Phillips screwdriver, a flathead screwdriver, a suction cup, and a spudger tool.
Step 2: Remove the Screws
Start by removing the two screws located on either side of the charging port at the bottom of the iPhone. Use the Phillips screwdriver to carefully unscrew them.
Next, use the suction cup to gently lift the screen away from the body of the iPhone. Be careful not to pull too hard or you may damage the cables that connect the screen to the phone.
Once the screen is detached, use the spudger tool to disconnect the cables that are holding the screen in place. Set the screen aside carefully.
Now, you should have access to the rear glass camera piece. Use the flathead screwdriver to carefully pry it out of its housing.
Finally, place the new rear glass camera piece into the housing and reassemble the phone by following these steps in reverse order. Make sure everything is securely in place before turning your iPhone back on.
Gather Necessary Tools and Materials
Before you begin replacing the rear glass camera piece on your iPhone 5s, make sure you have all the necessary tools and materials ready. Here is a list of what you will need:
| 1. Small Phillips screwdriver |
| 2. Pentalobe screwdriver |
| 3. Opening tool (such as a plastic spudger) |
| 4. Replacement rear glass camera piece |
| 5. Tweezers |
| 6. Adhesive strips or adhesive glue |
Having these tools and materials on hand will make the replacement process smoother and ensure you have everything you need to complete the task successfully.
Prepare Your Workspace
Before you start replacing the iPhone 5s rear glass camera piece, make sure you have a clean and well-lit workspace. Here are some tips to prepare your workspace:
- Gather all the necessary tools and replacement parts, including a small Phillips screwdriver, a flat tool (such as a plastic spudger), and the replacement rear camera glass piece.
- Find a flat surface to work on, preferably covered with a soft cloth or a non-slip mat to prevent any damage to your iPhone or the replacement part.
- Make sure you have enough space to lay out the components of your iPhone 5s and keep them organized during the repair process.
- Consider using a magnetic mat or a tray to keep track of the screws and small parts you remove from your iPhone.
- Keep a container handy to store the screws and small components to prevent them from rolling away or getting lost.
Remove the Back Cover of Your iPhone 5s
To replace the rear glass camera piece on your iPhone 5s, you will first need to remove the back cover of the device. Follow these steps to safely remove the back cover:
Step 1: Power Off Your iPhone
Before you begin, make sure your iPhone is powered off to avoid any risk of damage.
Step 2: Unscrew the Bottom Screws
Using a pentalobe screwdriver, carefully unscrew the two screws located on either side of the charging port at the bottom of your iPhone 5s.
| Left Side | Right Side |
| Unscrew Counterclockwise | Unscrew Counterclockwise |
Once the screws are removed, keep them in a safe place for reassembly later.
Disconnect the Camera Module
Before removing the rear glass camera piece, you need to disconnect the camera module from the iPhone 5s. To do this, locate the connector that attaches the camera module to the motherboard. Use a small screwdriver or plastic pry tool to carefully disconnect the connector by gently lifting it up.
Be sure to handle the camera module with care to avoid damaging it during the disconnection process. Once the connector is detached, you can proceed with removing the rear glass camera piece following the steps outlined in the guide.
Remove the Broken Glass Piece
Before you can replace the rear glass camera piece on your iPhone 5s, you need to remove the broken glass piece. Follow these steps carefully:
Step 1: Prepare the Tools
Gather the necessary tools, such as a small Phillips screwdriver, a suction cup, a plastic spudger, and a replacement rear glass camera piece.
Step 2: Remove the Screws
Use the small Phillips screwdriver to remove the two screws located next to the charging port on the bottom edge of the iPhone 5s.
Install the New Rear Glass Camera Piece
Once you have removed the old rear glass camera piece, it’s time to install the new one. Follow these steps to properly install the new rear glass camera piece on your iPhone 5s:
- Remove any adhesive residue left on the phone using a cleaning solution and a microfiber cloth.
- Peel off the protective film on the adhesive side of the new rear glass camera piece.
- Align the camera piece with the camera opening on the back of the phone.
- Gently press down on the camera piece to secure it in place.
- Make sure the camera piece is securely attached and flush with the phone’s surface.
- Once the camera piece is properly installed, you can proceed to reassemble your iPhone 5s following the previous steps in reverse order.
Additional Tips:
- Double-check the alignment of the camera piece before pressing it down to avoid any misalignment.
- Use caution when handling the adhesive side of the camera piece to prevent any damage or contamination.
Reassemble Your iPhone 5s
Now that you have successfully replaced the rear glass camera piece on your iPhone 5s, it’s time to reassemble the device. Follow these steps to put everything back together:
-
Step 1: Reattach the Rear Panel
Place the rear panel back onto the iPhone 5s, making sure it fits securely into place. Press down along the edges to ensure a snug fit.
-
Step 2: Reinstall the Screws
Using the Pentalobe screwdriver, reinsert the screws at the bottom of the iPhone 5s to secure the rear panel in place.
-
Step 3: Power On Your iPhone
Press and hold the power button until the Apple logo appears on the screen. Your iPhone 5s should now be fully reassembled and ready to use.
| Caution: If you encounter any issues or the camera is not functioning properly after reassembly, consider seeking professional help or consulting Apple Support. |
