Is your iPhone 7 Plus front facing camera not working properly? Are you experiencing blurry images or a malfunctioning camera app? It may be time to replace the front facing camera on your device. Fortunately, with the right tools and a little know-how, you can easily replace the camera yourself.
In this guide, we will walk you through the step-by-step process of replacing the front facing camera on your iPhone 7 Plus. Whether you’re a DIY enthusiast or just looking to save some money on repairs, this tutorial will help you get your device back up and running in no time.
Before you begin, make sure you have a replacement front facing camera that is compatible with the iPhone 7 Plus. You will also need a set of precision screwdrivers, a plastic opening tool, and a spudger tool. It’s important to work in a clean, well-lit area and take your time to avoid damaging your device.
Step-by-Step Guide to Replacing Front Facing Camera on iPhone 7 Plus
If you are experiencing issues with the front-facing camera on your iPhone 7 Plus, you may need to replace it. Here is a step-by-step guide to help you through the process:
| Step 1: | Turn off your iPhone and remove the two bottom screws next to the lightning port using a Pentalobe screwdriver. |
| Step 2: | Use a suction cup to lift the display assembly slightly and insert a plastic opening tool between the display and the rear case. Gently work your way around the edges to separate the display assembly. |
| Step 3: | Remove the screws securing the metal bracket over the front-facing camera and disconnect the front camera and sensor cable connectors. |
| Step 4: | Remove the front-facing camera and sensor assembly from the iPhone. |
| Step 5: | Install the new front-facing camera and sensor assembly by following the steps in reverse order. |
| Step 6: | Secure the metal bracket over the camera, reattach the display assembly, and tighten the screws. |
| Step 7: | Power on your iPhone to test the front-facing camera. If everything is working properly, you have successfully replaced the front camera on your iPhone 7 Plus. |
Gather Necessary Tools and Parts
Before you start replacing the front facing camera on your iPhone 7 Plus, make sure you have all the necessary tools and parts ready. Here is a list of tools and parts you will need:
Tools:
- Pentalobe screwdriver – for removing the screws at the bottom of the phone.
- Phillips screwdriver – for removing the internal screws.
- Suction cup – for lifting the display assembly.
- Spudger tool – for disconnecting cables and removing components.
- Tweezers – for handling small components.
Parts:
- Replacement front facing camera module – make sure it is compatible with the iPhone 7 Plus.
- Adhesive strips – for reattaching components securely.
Having these tools and parts ready will help you complete the camera replacement process smoothly and efficiently.
Power Off Your iPhone 7 Plus
To begin replacing the front facing camera on your iPhone 7 Plus, you will need to power off the device. Press and hold the power button located on the right side of the phone until the “slide to power off” option appears on the screen. Swipe the slider to turn off your iPhone 7 Plus.
Remove the Two Bottom Screws
Step 1: Start by powering off your iPhone 7 Plus.
Step 2: Locate the two pentalobe screws at the bottom of the phone next to the charging port.
Step 3: Use a pentalobe screwdriver to remove the two screws.
Step 4: Keep the screws in a safe place as you will need them later to reassemble your phone.
Separate the Display Assembly
To begin replacing the front facing camera on your iPhone 7 Plus, you will first need to separate the display assembly from the rest of the device. This step is crucial to access the internal components of the phone.
Start by powering off your iPhone and removing the two screws located next to the charging port. Use a pentalobe screwdriver to unscrew these screws.
Be Gentle and Patient
Next, gently lift the display assembly using a suction cup and a plastic opening tool. Be careful not to apply too much force, as you may damage the delicate components inside the phone. Take your time and work slowly to separate the display assembly from the rest of the device.
Once the display assembly is detached, you will have access to the front facing camera and other internal components that may need replacement.
Disconnect the Front Camera and Sensor Cable
1. Use a small Phillips screwdriver to remove the two screws holding the metal bracket in place.
2. Gently lift the metal bracket and set it aside.
3. Locate the front camera and sensor cable connector on the logic board.
4. Carefully disconnect the front camera and sensor cable by gently prying it up from the connector on the logic board.
5. Ensure that the cable is completely disconnected before proceeding with the replacement.
Remove the Front Camera Bracket
Once you have disconnected the front camera flex cable, you can proceed to remove the front camera bracket. The bracket is held in place by several screws, typically Phillips screws. Use the appropriate screwdriver to carefully remove these screws and set them aside in a safe place.
After removing the screws, gently lift the front camera bracket out of its place. Be cautious not to damage any surrounding components or cables. Once the bracket is removed, you can access the front-facing camera module and proceed with replacing it.
Replace the Front Facing Camera
If you need to replace the front facing camera on your iPhone 7 Plus, follow these steps:
- Power off your device and remove the two bottom screws located next to the charging port.
- Use a suction cup to lift the front panel, then carefully open the device by swinging the screen up.
- Remove the screws securing the metal plate covering the front facing camera and disconnect the flex cable.
- Take out the damaged front facing camera and replace it with a new one.
- Reassemble the device by following the steps in reverse order and power it on to test the new front facing camera.
Reconnect the Front Camera and Sensor Cable
Once you have replaced the front facing camera on your iPhone 7 Plus, it’s time to reconnect the front camera and sensor cable. Follow these steps:
- Position the front camera and sensor cable: Carefully align the front camera and sensor cable with the connector on the logic board.
- Reconnect the cable: Gently press the cable into the connector on the logic board until it snaps into place. Be sure to align the connector properly to avoid damaging the cable.
- Secure the cable: Once the cable is connected, make sure to secure it in place using the metal bracket or adhesive tape provided.
- Test the front camera: Before reassembling your iPhone, test the front camera to ensure it is functioning correctly. Open the camera app and switch to the front-facing camera to check for any issues.
By following these steps, you can successfully reconnect the front camera and sensor cable on your iPhone 7 Plus after replacing the front facing camera.
Reassemble Your iPhone 7 Plus
Once you have successfully replaced the front facing camera on your iPhone 7 Plus, it’s time to reassemble the device. Follow these steps:
| 1. | Place the front panel back onto the device, making sure to align the clips along the edges. |
| 2. | Secure the front panel with the screws you removed earlier. |
| 3. | Reconnect the cables for the front facing camera and other components. |
| 4. | Replace the display assembly and press down firmly to secure it in place. |
| 5. | Power on your iPhone 7 Plus and test the front facing camera to ensure it is functioning properly. |
