If you have noticed that the camera lens cover on your iPhone 6 is scratched or cracked, it may be affecting the quality of your photos. Luckily, you can replace the rear camera lens cover yourself with just a few tools and a bit of patience. In this guide, we will walk you through the steps to safely remove the rear camera lens cover on your iPhone 6.
Step 1: Start by powering off your iPhone and removing the SIM card tray. This will prevent any damage to the phone during the lens replacement process. Use a SIM card eject tool or a paperclip to gently push into the small hole on the side of the phone to release the tray.
Step 2: Next, you will need a small Phillips screwdriver to remove the two screws located near the charging port on the bottom of the phone. Once the screws are removed, gently pry off the bottom panel of the phone to reveal the rear camera assembly.
Step-by-Step Guide to Removing iPhone 6 Rear Camera Lens Cover
Removing the rear camera lens cover on your iPhone 6 may seem like a daunting task, but with the right tools and technique, you can do it yourself. Here is a step-by-step guide to help you through the process:
Step 1: Gather the Necessary Tools
Before you start, make sure you have the following tools ready: a small Phillips screwdriver, a plastic opening tool, and a replacement camera lens cover if needed.
Step 2: Remove the Screws
Use the small Phillips screwdriver to remove the screws located around the camera lens cover. Be sure to keep the screws in a safe place as you will need them to reassemble the cover later.
Gather Necessary Tools
Before you begin the process of removing the rear camera lens cover on your iPhone 6, make sure you have the following tools ready:
- Small Phillips screwdriver
- Prying tool or plastic opening tool
- Replacement rear camera lens cover (if needed)
- Clean cloth or microfiber towel
Having these tools on hand will help you complete the task efficiently and without causing any damage to your device.
Power Off Your iPhone 6
Before you begin the process of removing the rear camera lens cover on your iPhone 6, make sure to power off the device. This step is crucial to prevent any accidental damage to the phone or injury to yourself. To power off your iPhone 6, press and hold the power button located on the right side of the device until the “slide to power off” option appears on the screen.
Once the “slide to power off” option appears, slide it to the right to turn off your iPhone 6. Wait for the device to completely power down before proceeding with the next steps to remove the rear camera lens cover.
Remove the Two Pentalobe Screws
To access the rear camera lens cover on your iPhone 6, you will need to remove the two pentalobe screws located next to the charging port. These screws are small and have a unique star-shaped head, so you will need a pentalobe screwdriver to remove them.
Before you begin, make sure your iPhone is powered off and disconnect any cables. Using the pentalobe screwdriver, carefully unscrew the two screws and set them aside in a safe place. Be gentle while removing the screws to avoid stripping them or damaging the screw heads.
Use a Suction Cup to Lift the Display
To start the process of removing the iPhone 6 rear camera lens cover, you will need to use a suction cup to lift the display. This step is crucial to gain access to the internal components of the device.
- Place the suction cup near the Home button of the iPhone 6.
- Gently pull up on the suction cup to create a small gap between the display and the rear case.
- Insert a plastic opening tool or a guitar pick into the gap to keep it open.
- Slide the opening tool around the edges of the iPhone to separate the display from the rear case.
By following these steps, you can successfully lift the display of the iPhone 6 using a suction cup, making it easier to access and remove the rear camera lens cover.
Unscrew the Metal Plate Covering the Rear Camera
To access the rear camera lens cover on your iPhone 6, you will need to unscrew the metal plate that covers it. Follow these steps to remove the metal plate:
- Use a small Phillips head screwdriver to remove the screws holding the metal plate in place.
- Gently lift the metal plate off the camera module to expose the lens cover underneath.
Disconnect the Rear Camera Connector
Before removing the rear camera lens cover, you will need to disconnect the rear camera connector. This connector is located on the motherboard near the rear camera module.
- Use a plastic spudger tool to gently pry up the connector latch.
- Once the latch is lifted, carefully disconnect the rear camera connector by pulling it straight out from the motherboard.
- Be gentle and ensure that you do not apply too much force to avoid damaging the connector or the motherboard.
With the rear camera connector disconnected, you can proceed to remove the rear camera lens cover following the appropriate steps.
Heat the Rear Camera Lens Cover
To remove the rear camera lens cover on your iPhone 6, you can start by heating the cover. Use a hairdryer or a heat gun on a low setting to gently warm up the adhesive underneath the cover. Be careful not to overheat the cover, as excessive heat can damage the camera components. Heat the cover for about 1-2 minutes to soften the adhesive.
Remove the Adhesive Holding the Lens Cover
Once you have heated the lens cover, you can start removing the adhesive holding it in place. Use a sharp and thin tool, like a razor blade or a thin plastic prying tool, to carefully lift the edges of the lens cover.
Be gentle and take your time to avoid damaging the camera lens or the surrounding components. Slowly work your way around the edges of the lens cover, applying slight pressure to loosen the adhesive.
Continue until the lens cover is completely detached from the rear camera. Make sure to keep track of any adhesive residue that may be left behind on the camera or the lens cover.
Replace the Rear Camera Lens Cover
If you need to replace the rear camera lens cover on your iPhone 6, follow these steps:
Step 1: Gather the Necessary Tools
Before you begin, make sure you have a replacement camera lens cover and the necessary tools, such as a small Phillips screwdriver and a plastic pry tool.
Step 2: Remove the Old Lens Cover
Use the plastic pry tool to gently pry off the old camera lens cover. Be careful not to damage the surrounding components.
Note: If the lens cover is cracked or shattered, be extra cautious as broken glass can cause injury.
Once the old lens cover is removed, clean any residue or adhesive from the camera module.
Caution: Take care not to get any debris or dust on the camera lens itself.
Align the new camera lens cover over the camera module and press it into place. Make sure it is securely attached.
Finally, reassemble your iPhone 6 by following the steps in reverse order.
Reassemble Your iPhone 6
Once you have successfully removed the rear camera lens cover from your iPhone 6, it’s time to reassemble the device. Follow these steps to put everything back together:
![Simtect for Samsung Galaxy S24 Ultra Case with Camera Cover, [Non-Yellowing] [Military Drop Protection], Slim Protective Hard Back and Soft Edge Phone Case for Galaxy S24 Ultra Case 6.8 Inches, Clear](https://m.media-amazon.com/images/I/51Ji1BuLyaL._SS520_.jpg)
- Place the rear camera lens cover back into its position on the iPhone 6.
- Make sure the lens cover is securely in place and aligned properly.
- Carefully reattach any screws or clips that were removed during the disassembly process.
- Gently press down on the lens cover to ensure it is properly seated.
- Replace the back cover of the iPhone 6 and secure it with the screws.
- Power on your iPhone 6 to test the rear camera and ensure it is functioning correctly.
Final Steps
- If the rear camera is working properly, congratulations! You have successfully reassembled your iPhone 6.
- If you encounter any issues with the camera or the device, double-check the reassembly steps and try again.
