If you’re experiencing issues with the front-facing camera on your iPhone 6s Plus, you may need to replace or remove it. The front-facing camera, also known as the selfie camera, is an essential component of the phone, allowing you to take selfies, make video calls, and use FaceTime. If the camera is damaged or not working properly, you can follow these steps to remove it and replace it with a new one.
Step 1: Turn off your iPhone 6s Plus and make sure it is unplugged from any power source. This will ensure your safety while working on the device.
Step 2: Use a small Phillips screwdriver to remove the screws on the bottom of the phone. These screws hold the front-facing camera module in place.
Step-by-Step Guide to Removing Front Facing Camera on iPhone 6s Plus
Removing the front facing camera on an iPhone 6s Plus can be a delicate process, but with the right tools and careful steps, it can be done successfully. Here is a step-by-step guide to help you through the process:
Step 1: Power off your iPhone 6s Plus and remove the SIM card tray.
Step 2: Use a Pentalobe screwdriver to remove the two screws located at the bottom of the phone next to the charging port.
Step 3: Place a suction cup near the home button and gently pull to create a small gap between the screen and the frame.
Step 4: Slide an opening tool or a plastic card along the seam to release the clips holding the screen in place. Be careful not to damage the cables connecting the screen to the phone.
Step 5: Lift the screen assembly up and prop it at a 90-degree angle using an iPhone stand or something similar.
Step 6: Locate the front facing camera module near the top of the phone and disconnect the cable attached to it.
Step 7: Unscrew the two screws holding the camera module in place and carefully lift it out of the phone.
Step 8: Replace the front facing camera with a new one if needed, then reverse the steps to reassemble your iPhone 6s Plus.
By following these steps carefully and patiently, you can successfully remove the front facing camera on your iPhone 6s Plus. Remember to take your time and be gentle to avoid causing any damage to your device.
Tools Required for the Procedure
1. Small Phillips Screwdriver: You will need a small Phillips screwdriver to remove the screws holding the front facing camera in place.
2. Plastic Opening Tools: Plastic opening tools are essential for prying open the iPhone 6s Plus without causing damage to the casing or screen.
3. Tweezers: Tweezers will come in handy for handling small components and connectors during the removal process.
4. Spudger: A spudger tool can help you disconnect the cables and connectors without damaging them.
5. Suction Cup: A suction cup can be useful for lifting the front panel and creating separation between the display assembly and the rest of the phone.
6. Adhesive Strips: You may need adhesive strips to reattach the front facing camera and secure it in place after the replacement.
7. Cleaning Cloth: A cleaning cloth is handy for wiping down the components and screen before reassembly.
Preparation Steps Before Removing the Front Facing Camera
Before attempting to remove the front facing camera on your iPhone 6s Plus, it is important to take the following preparation steps:
- Power off your iPhone and make sure it is disconnected from any power source.
- Gather all the necessary tools for the camera removal process, such as a small Phillips screwdriver, a spudger tool, and a suction cup.
- Prepare a clean and well-lit workspace with a soft surface to prevent damage to your phone.
- Back up any important data on your phone to prevent loss of information during the repair.
Removing the Display Assembly
To remove the front facing camera on your iPhone 6s Plus, you will first need to remove the display assembly. Here’s how you can do it:
1. Power off your iPhone and remove the two screws located at the bottom of the device near the charging port.
2. Use a suction cup to lift the display assembly slightly. Insert a plastic opening tool or a spudger between the display assembly and the rear case.
3. Carefully pry the display assembly up from the rear case, making sure not to damage the cables connecting the display to the logic board.
4. Once the display assembly is separated from the rear case, you can access the front facing camera module located near the top of the device.
5. Disconnect the front facing camera cable from the logic board and remove the screws holding the camera module in place.
6. Gently lift the front facing camera module out of its housing and replace it with a new one if needed.
7. Reassemble your iPhone by following these steps in reverse order, making sure to carefully reconnect all cables and secure the display assembly back onto the rear case.
Disconnecting the Front Camera and Sensor Cable
To remove the front-facing camera on your iPhone 6s Plus, you will need to disconnect the front camera and sensor cable. Here’s how to do it:
- Power off your iPhone and remove the two bottom screws near the lightning connector.
- Use a suction cup to lift the display assembly slightly and insert a plastic opening tool between the display and the rear case.
- Slowly open the iPhone, being careful not to damage the cables connecting the display to the logic board.
- Locate the front camera and sensor cable connector near the top of the phone.
- Use a spudger or a plastic opening tool to carefully disconnect the front camera and sensor cable from the logic board.
- Once the cable is disconnected, you can safely remove the front-facing camera from your iPhone 6s Plus.
Remember to follow these steps carefully and take your time to avoid causing any damage to your device.
Removing the Front Camera and Sensor Assembly
To remove the front camera and sensor assembly from your iPhone 6s Plus, follow these steps:
Step 1: Gather the Necessary Tools
Before you begin, make sure you have the following tools: a Pentalobe screwdriver, a Phillips screwdriver, a spudger tool, and a suction cup.
Step 2: Remove the Display Assembly
Start by removing the display assembly of your iPhone 6s Plus. Use the Pentalobe screwdriver to remove the screws at the bottom of the device, then use the suction cup to lift the display assembly.
| 1 | Remove the screws at the bottom of the device |
| 2 | Lift the display assembly with the suction cup |
Installing a New Front Facing Camera on iPhone 6s Plus
If you need to replace the front facing camera on your iPhone 6s Plus, you can do it yourself with some basic tools and a replacement camera module. Follow these steps to install a new front facing camera:
Step 1: Gather the Necessary Tools
Before you begin, make sure you have the following tools ready:
| – Screwdriver set |
| – Plastic opening tools |
| – Replacement front facing camera module |
Step 2: Remove the Old Camera
1. Power off your iPhone 6s Plus and remove the screws at the bottom of the phone using the screwdriver set.
2. Use the plastic opening tools to carefully pry open the display assembly.
3. Locate the front facing camera module and disconnect the flex cable attached to it.
4. Remove the screws holding the camera in place and gently lift it out of the phone.
Be careful not to damage any other components while removing the old camera.
Once you have removed the old camera, you can proceed to install the new front facing camera module following the same steps in reverse order. Make sure to test the new camera after installation to ensure it is working properly.
Reassembling the iPhone 6s Plus After Front Camera Replacement
After successfully replacing the front facing camera on your iPhone 6s Plus, it’s time to reassemble the device to ensure everything is put back together correctly. Follow these steps to complete the reassembly process:
Step 1: Carefully place the front camera and sensor assembly back into its position on the front panel assembly, making sure all the connectors are properly aligned.
Step 2: Gently lower the display assembly onto the body of the iPhone, ensuring that the display cables are not pinched or trapped between the display and the body.
Step 3: Reconnect all the display and front camera connectors, making sure they are securely in place.
Step 4: Carefully align the clips along the sides of the iPhone and press down on the display assembly to snap them into place.
Step 5: Insert the screws back into their respective positions on the display assembly, securing it to the body of the iPhone.
Step 6: Power on your iPhone to test the front camera and display functionality to ensure everything is working properly.
Step 7: If everything is working correctly, you have successfully reassembled your iPhone 6s Plus after front camera replacement. Congratulations!
