Have you accidentally cracked the back camera glass on your iPhone 6 Plus? Don’t worry, you can easily replace it yourself with a few simple tools and steps. In this guide, we will show you how to safely remove the damaged camera glass and install a new one without any hassle.
Step 1: Gather the Necessary Tools
Before you begin, make sure you have the right tools for the job. You will need a small Phillips screwdriver, a heat gun or hairdryer, a suction cup, a plastic spudger, and a replacement camera glass for iPhone 6 Plus.
Step 2: Heat and Loosen the Adhesive
Use the heat gun or hairdryer to gently heat the edges of the back camera glass. This will soften the adhesive holding it in place. Once the adhesive is warm, use the suction cup to lift the glass slightly. Insert the plastic spudger into the gap to loosen the adhesive further.
Step-by-step Guide to Removing Back Camera Glass on iPhone 6 Plus
If you need to replace or repair the back camera glass on your iPhone 6 Plus, you can follow these steps to safely remove it without causing damage to your device.
Step 1:
Power off your iPhone 6 Plus and make sure it is completely turned off before starting the removal process.
Step 2:
Use a small Phillips screwdriver to remove the two screws located next to the charging port on the bottom of the phone.
Step 3:
Place a suction cup near the bottom edge of the back cover and gently lift to create a small gap between the cover and the body of the phone.
Step 4:
Slide a plastic opening tool or a guitar pick along the edge of the phone to separate the back cover from the body. Be careful not to apply too much pressure to avoid damaging the phone.
Step 5:
Once the back cover is removed, locate the back camera glass and carefully lift it from the housing using a plastic opening tool or a pair of tweezers.
Step 6:
Inspect the camera glass for any adhesive residue or debris that needs to be cleaned before installing the new camera glass.
Step 7:
Install the new camera glass by gently pressing it into place on the housing of the phone.
Step 8:
Reattach the back cover of the iPhone 6 Plus by aligning it properly and gently pressing it into place until it snaps back into position.
Step 9:
Secure the two screws next to the charging port to complete the installation process.
That’s it! You have successfully removed and replaced the back camera glass on your iPhone 6 Plus. Remember to test the camera functionality after reassembly to ensure everything is working properly.
Gather Necessary Tools
Before you begin removing the back camera glass on your iPhone 6 Plus, make sure you have all the necessary tools on hand. Here’s a list of tools you’ll need:
| 1. Small Phillips screwdriver |
| 2. Prying tool or plastic opening tool |
| 3. Suction cup |
| 4. Tweezers |
| 5. Replacement camera glass (if needed) |
Power Off Your iPhone 6 Plus
Before starting the process of removing the back camera glass on your iPhone 6 Plus, it is essential to power off the device to prevent any damage or accidents. Follow these steps to power off your iPhone:
- Press and hold the power button located on the right side or top of your iPhone.
- Slide the “Slide to power off” slider that appears on the screen to turn off your device.
- Wait for the iPhone to power off completely before proceeding with the removal process.
Ensuring that your iPhone is powered off will help you safely work on removing the back camera glass without any risk of causing harm to your device.
Remove the Rear Panel
To access the back camera glass on your iPhone 6 Plus, you’ll first need to remove the rear panel of the phone. Here’s how to do it:
- Power off your iPhone: Make sure your phone is turned off before starting the disassembly process.
- Remove the screws: Use a pentalobe screwdriver to remove the two screws located next to the Lightning connector on the bottom of the phone.
- Heat the adhesive: Use a heat gun or hair dryer to gently heat the edges of the rear panel. This will soften the adhesive, making it easier to remove.
- Use a suction cup: Once the adhesive is heated, place a suction cup near the home button and gently pull to create a small gap between the rear panel and the frame.
- Slide a plastic opening tool: Slide a plastic opening tool or a guitar pick along the edges of the phone to separate the rear panel from the frame. Be careful not to damage the cables inside.
- Remove the rear panel: Once you’ve loosened the adhesive and separated the rear panel from the frame, carefully lift the panel away from the phone. Set it aside in a safe place.
With the rear panel removed, you can now access the back camera glass on your iPhone 6 Plus for replacement or repair.
Locate the Back Camera Glass
Before removing the back camera glass on your iPhone 6 Plus, you need to locate its position on the back of your device. The back camera glass is located near the top left corner of the phone, right above the rear camera lens.
Heat the Adhesive Around the Camera Glass
Using a heat gun or a hairdryer on low heat setting, carefully apply heat around the edges of the camera glass. This will help soften the adhesive holding the glass in place and make it easier to remove.
Be cautious not to overheat the glass or surrounding components to avoid damage.
Once the adhesive is sufficiently softened, gently pry the camera glass up using a thin tool like a plastic opening tool or a guitar pick. Work your way around the edges to gradually lift the glass without applying too much pressure.
Continue heating and prying until the camera glass is completely detached from the device.
Carefully Pry the Camera Glass Out
After heating the adhesive around the camera glass, use a plastic spudger or a pry tool to carefully lift the camera glass out of its housing. Work slowly and gently to avoid damaging the camera or the surrounding components. Be cautious not to apply too much pressure, as it may crack the glass or cause damage to the camera module.
Clean the Area and Camera Lens
Before installing the new back camera glass, it’s essential to clean the area thoroughly. Use a microfiber cloth to wipe away any dust, dirt, or residue from the camera lens and surrounding area. Make sure to be gentle to avoid scratching the lens or the phone’s body.
Next, use a cleaning solution specifically designed for electronics or a mixture of water and isopropyl alcohol to clean the camera lens. Apply the solution to a clean microfiber cloth and gently wipe the lens in a circular motion. Avoid using excessive pressure, as it may damage the lens.
Install the New Camera Glass
Once you have removed the old camera glass, it’s time to install the new one. Make sure the new camera glass is clean and free from any dust or debris.
Step 1: Carefully place the new camera glass in the opening on the back of the iPhone 6 Plus. Ensure that it fits snugly into place.
Step 2: Gently press down on the edges of the camera glass to secure it in place. Be careful not to apply too much pressure to avoid cracking or damaging the glass.
Final Check
Give the camera glass a final inspection to ensure it is securely installed and free from any smudges or fingerprints. Once you are satisfied with the installation, you can proceed to reassemble your iPhone 6 Plus.
Reattach the Rear Panel
Once you have successfully removed the back camera glass on your iPhone 6 Plus, it’s time to reattach the rear panel. Make sure the adhesive is still sticky enough to hold the panel in place. Align the panel with the edges of the phone and press firmly to secure it back into position.
Be gentle while reattaching the rear panel to avoid any damage to the components inside the phone. Once the panel is securely in place, you can power on your iPhone 6 Plus and test the camera to ensure it’s functioning properly.
Power On Your iPhone and Test the Camera
Before reassembling your iPhone, it’s important to power it on and test the camera to ensure that everything is working properly. Press the power button to turn on your iPhone and open the camera app. Take a few test photos and videos to check if the camera is functioning correctly. If you notice any issues with the camera, double-check the connections and make sure everything is properly reassembled before trying again.
