Carmen J. Moore
If you own an iPhone 7 Plus and have unfortunately cracked or scratched the glass covering the camera lens, you may be wondering how to replace it. While it can be a daunting task, with the right tools and guidance, you can successfully replace the glass on your iPhone 7 Plus camera.
In this guide, we will walk you through the step-by-step process of replacing the glass on the camera of your iPhone 7 Plus. From gathering the necessary tools to carefully removing the old glass and installing the new one, we will provide detailed instructions to help you complete this repair.
Whether you are a DIY enthusiast or simply looking to save money on costly repairs, learning how to replace the glass on the camera of your iPhone 7 Plus can be a rewarding experience. Follow our guide and restore your camera lens to its original condition.
Step-by-step guide to replacing glass on camera for iPhone 7 Plus
If you’ve accidentally cracked the glass covering the camera lens on your iPhone 7 Plus, you may be able to replace it yourself with some basic tools and a steady hand. Follow these steps to safely replace the glass on the camera:
Step 1: Gather the necessary tools
Before you begin, make sure you have a replacement camera glass cover, a small Phillips screwdriver, a heat gun or hairdryer, a suction cup, and a plastic pry tool.
Step 2: Remove the broken glass
Use the heat gun or hairdryer to heat the broken glass cover for about 1-2 minutes. Once it’s warm, use the suction cup to pull the glass away from the camera lens. Be careful not to apply too much pressure to avoid damaging the camera.
Important: Be sure to wear gloves and eye protection during this step to avoid injury from broken glass.
Continue to gently pry the glass away from the camera until it is completely removed.
Prepare necessary tools
Before you start replacing the glass on your iPhone 7 Plus camera, make sure you have all the necessary tools handy. Here are the tools you will need:
- Replacement glass: Make sure you have a high-quality replacement glass specifically designed for the iPhone 7 Plus camera.
- Small Phillips screwdriver: You will need this to remove the screws securing the camera glass.
- Plastic prying tool: This tool will help you safely pry off the old glass without damaging the camera.
- Clean cloth: A clean cloth will be useful for wiping off any dust or debris from the camera lens.
- Tweezers: Tweezers can come in handy for handling small parts and screws during the replacement process.
Having these tools ready will make the glass replacement process much smoother and ensure you have everything you need to complete the task successfully.
Turn off the iPhone
Before you start replacing the glass on the camera of your iPhone 7 Plus, make sure to turn off the device to avoid any potential damage or accidents during the process.
Remove the screws
Before you can access the camera glass on your iPhone 7 Plus, you’ll need to remove the screws that secure the back cover in place. To do this, you’ll need a small Phillips screwdriver. Here’s how:
| 1. | Power off your iPhone and lay it on a clean, flat surface. |
| 2. | Locate the two screws on either side of the charging port at the bottom of the phone. |
| 3. | Use the Phillips screwdriver to carefully unscrew these two screws. Make sure to keep the screws in a safe place where you won’t lose them. |
Detach the camera module
To detach the camera module from the iPhone 7 Plus, carefully disconnect the ribbon cable that connects the camera module to the motherboard. Use a plastic spudger or a pair of tweezers to gently lift the connector latch and slide out the ribbon cable. Be sure to handle the delicate ribbon cable with care to avoid damaging it.
Replace the glass
If you need to replace the glass on the camera of your iPhone 7 Plus, follow these steps:
Step 1: Gather the necessary tools
Before you begin, make sure you have the following tools on hand: a small Phillips screwdriver, a flat tool like a plastic spudger, a heat gun or hair dryer, and a replacement glass for the camera.
Step 2: Disassemble the phone
Start by removing the screws around the camera lens using the Phillips screwdriver. Then use the flat tool to carefully pry off the broken glass from the camera module.
Assemble the iPhone
Once you have replaced the broken glass on the camera of your iPhone 7 Plus, it’s time to reassemble the device. Here’s how to do it:
- Place the rear camera module back into its housing on the iPhone.
- Reattach the camera module with the screws you removed earlier.
- Connect the camera flex cable back to the motherboard and secure it in place.
- Replace the metal bracket that covers the camera flex cable connector.
- Reinstall the logic board and battery into the iPhone.
- Reconnect all the cables and connectors, making sure they are properly seated.
- Put the display assembly back onto the iPhone and secure it with the screws.
- Power on your iPhone and test the rear camera to ensure it’s functioning properly.
I tried replacing the camera glass on my iPhone 7 Plus, and I have to say, it's not for the faint of heart! The instructions were good, but I definitely recommend watching a video to see how it's done. I accidentally cracked the camera module itself because I was too aggressive with the pry tool. Thankfully, I found a replacement online. Just be gentle and patient!
I have a cracked camera glass on my iPhone 7 Plus, but I'm worried about damaging something inside while replacing it. Has anyone done this themselves? How hard is it really?
How does replacing the glass compare to just getting the whole camera module replaced? Is it worth the trouble?