Are you looking to replace or repair the camera on your iPhone 7 Plus? If so, you’ll need to know how to safely remove it without causing any damage. Fortunately, with the right tools and a bit of patience, you can easily take the camera off of your iPhone 7 Plus following the instructions from iFixit.
iFixit is a well-known resource for DIY repair guides and teardowns of electronic devices, providing detailed steps and images to help you navigate the inner workings of your gadgets. In this guide, we’ll walk you through the process of removing the camera from your iPhone 7 Plus using iFixit’s expert advice.
Before you begin, it’s important to gather the necessary tools, such as a spudger, suction cup, screwdriver, and tweezers. Additionally, make sure to follow each step carefully and exercise caution to avoid causing any harm to your device. Let’s dive into the step-by-step instructions for removing the camera from your iPhone 7 Plus.
Step-by-Step Guide for Removing Camera from iPhone 7 Plus
If you need to replace or repair the camera on your iPhone 7 Plus, follow these steps to safely remove it:
- Power off your iPhone 7 Plus and remove any SIM card tray.
- Remove the two 3.4 mm pentalobe screws located at the bottom of the phone near the charging port.
- Use a suction cup to lift the display assembly slightly and insert a plastic opening tool between the display and the rear case.
- Slide the opening tool along the bottom edge of the phone to separate the display assembly from the rear case.
- Once the display is partially separated, tilt it away from the top edge of the phone to access the camera module.
- Locate the camera module near the top edge of the phone and disconnect the flex cable attached to it.
- Remove the screws securing the camera module in place and carefully lift it out of the phone.
- Replace the camera module with a new one if needed, and follow these steps in reverse to reassemble your iPhone 7 Plus.
By following these steps carefully, you can successfully remove the camera from your iPhone 7 Plus for replacement or repair.
Prepare Necessary Tools for Disassembling
Before you begin the process of taking the camera off of your iPhone 7 Plus, make sure you have the following tools on hand:
- Pentalobe screwdriver: You will need this to remove the screws holding the back cover in place.
- Phillips screwdriver: This tool will be necessary for removing internal screws during the disassembly process.
- Plastic opening tools: These tools are essential for prying open the iPhone without causing damage to the delicate components.
- Suction cup: A suction cup will help you lift the screen and access the internal components of the phone.
- Tweezers: Tweezers will come in handy for handling small screws and other tiny components.
- Spudger: A spudger can help you disconnect cables and pry apart components without damaging them.
Having these tools ready will ensure a smooth disassembly process and minimize the risk of causing damage to your iPhone 7 Plus.
Power Off Your iPhone 7 Plus Before Starting the Process
Before you begin the process of taking the camera off your iPhone 7 Plus, it is crucial to power off the device to prevent any potential damage. To power off your iPhone 7 Plus, press and hold the power button located on the right side of the device until the “slide to power off” slider appears on the screen. Slide the slider to turn off the device completely before proceeding with the camera removal process.
Remove the Pentalobe Screws from the Bottom of the Device
To start the process of taking the camera off your iPhone 7 Plus, you will need to remove the two Pentalobe screws located at the bottom edge of the device near the charging port. Use a Pentalobe screwdriver to carefully unscrew these two screws.
Note: Make sure to keep track of these screws as you will need them to reassemble the device later.
Use a Suction Handle to Lift the Display Assembly
If you are having trouble removing the display assembly, you can use a suction handle to help lift it off the iPhone 7 Plus. Follow these steps:
| 1. | Place the suction handle on the lower part of the display assembly, close to the home button. |
| 2. | Press down on the suction handle to create a seal between the handle and the display assembly. |
| 3. | Slowly lift the suction handle upwards while holding the iPhone securely with your other hand. |
| 4. | Continue to lift the display assembly until it is fully separated from the iPhone 7 Plus. |
| 5. | Be careful not to apply too much force or twist the display assembly, as this can damage the delicate components inside. |
Disconnect the Display Assembly from the Logic Board
To disconnect the display assembly from the logic board, follow these steps:
- Remove the four Phillips screws securing the bracket covering the front panel sensor assembly connector.
- Remove the bracket.
- Use a spudger to disconnect the front panel sensor assembly connector from its socket on the logic board.
- Remove the following screws securing the display cable connector bracket:
- Three Phillips screws
- One tri-point screw
- Remove the bracket.
- Use a spudger to disconnect the display cable connector from its socket on the logic board.
Locate and Unscrew the Bracket Securing the Camera Module
To access the camera module on your iPhone 7 Plus, you will need to locate and unscrew the bracket that secures it in place. This bracket holds the camera module securely within the device and must be removed before you can take the camera off.
Step 1: Using a small Phillips screwdriver, carefully unscrew the screws that are holding the bracket in place. Make sure to keep track of the screws as you remove them.
Step 2: Once all the screws are removed, gently lift the bracket off of the camera module. Be careful not to damage any of the components surrounding the camera.
Note: It is important to handle the camera module with care to avoid any damage to the delicate components.
Carefully Lift and Remove the Camera Module from the Device
Once you have disconnected the camera module from the logic board, you can carefully lift it from the device. Be gentle to avoid damaging any delicate components.
Make sure to keep track of any screws or brackets that were removed during the process, as you will need them for reassembly.
Replace the Camera Module with a New One if Necessary
If you have determined that the camera module on your iPhone 7 Plus needs to be replaced, you can follow these steps to do so:
Tools Required:
- Replacement camera module
- Pentalobe screwdriver
- Phillips screwdriver
- Spudger tool
- Suction cup
- Heat gun or hair dryer
Here is a step-by-step guide on how to replace the camera module:
| Step | Instructions |
| 1 | Power off your iPhone and remove the screws at the bottom using a Pentalobe screwdriver. |
| 2 | Use a suction cup to lift the display assembly and then use a spudger tool to carefully separate the display from the device. |
| 3 | Locate the camera module on the back of the device and remove the screws holding it in place using a Phillips screwdriver. |
| 4 | Disconnect the cables attached to the camera module and carefully pry it out of its housing. |
| 5 | Place the new camera module in the housing and reattach the cables. |
| 6 | Secure the camera module with the screws and reassemble the device by following the steps in reverse order. |
| 7 | Power on your iPhone and test the new camera module to ensure it is functioning properly. |
Reassemble Your iPhone 7 Plus by Following the Steps in Reverse Order
Once you have successfully removed the camera from your iPhone 7 Plus and completed any necessary repairs or maintenance, it’s time to reassemble the device. Follow these steps in reverse order to put everything back together:
- Insert the camera module back into its slot on the rear case.
- Reconnect the camera module flex cable to the logic board.
- Secure the camera module in place with the screws you removed earlier.
- Reattach the shield plate over the camera module and secure it with the screws.
- Carefully reposition the rear case onto the iPhone, ensuring that all the clips snap back into place.
- Replace the screws along the perimeter of the iPhone to secure the rear case.
- Turn on your iPhone 7 Plus to test the camera and ensure everything is functioning properly.
By following these steps in reverse order, you can reassemble your iPhone 7 Plus and enjoy a fully functional camera once again.
